Close

Añadido correctamente

El producto se ha añadido a su cotización.

ABB ACH580 vs ACH550 for HVAC Fans and Pumps | Industrial Automation Co.

IAC blog / ABB drives

ABB ACH580 and ACH550HVAC drives for fans and pumps, and how to choose

Most fans and pumps in a building are sized for the hottest, busiest day of the year, then run faster than they need to the rest of the time. An HVAC drive fixes that. Here is where ABB’s ACH580 and ACH550 fit, how they save energy, and which one to pick.

Get a quote Call 1-877-727-8757

ACH580-01-065A-4

ABB ACH580 HVAC drive, 65 A, 380–480 V. Check availability or request a quote.

Request a quote

ACH550-UH-125A-4

ABB ACH550 HVAC drive, 125 A, 380–480 V. Direct replacement for existing ACH550 installs.

Request a quote

Why fans and pumps get the biggest payback from a drive

Centrifugal fans and pumps follow the affinity laws. Flow changes in step with speed, but the power the motor draws changes with the cube of speed. Slow a fan down a little and its energy use drops a lot: at 80% speed, the theoretical power draw is about half.

Compare that with the older ways of controlling flow. A damper or throttling valve lets the motor run flat out and then chokes the air or water downstream, so the motor still pulls close to full power. A drive simply turns the motor slower.

Real-world savings come in below the curve because of static pressure, system losses and minimum-speed limits. Even so, fans and pumps are where a drive usually pays for itself fastest.

Where ACH580 and ACH550 drives go to work

  • Air handlers: supply and return fans tracking duct static pressure, the most common HVAC drive application.
  • Cooling towers: tower fans slowing down as condenser water temperature allows.
  • Chilled and condenser water pumps: variable-flow loops that follow building load instead of running at constant speed.
  • Hot water and boiler loops: circulation pumps held at a differential pressure setpoint.
  • Booster pumps and exhaust fans: domestic water pressure, parking garage and kitchen exhaust.

What makes an HVAC drive different

Any VFD can spin a fan. ABB’s ACH line is built around what building engineers and controls contractors deal with every day.

It talks to the building automation system

Both families have embedded fieldbus for common building protocols, including BACnet MS/TP and Modbus RTU, so the BMS can start, stop, set speed and read back current, faults and energy without extra hardware. Confirm protocol support for your model and firmware in the manual.

Hand-Off-Auto at the keypad

Technicians can put a fan or pump in hand mode for testing and hand it back to the BMS without touching the wiring.

Built-in PID and sleep for pumps

The drive can hold a pressure or temperature setpoint on its own, then sleep when demand drops and wake when it returns, so pumps don’t run all night at minimum speed.

Override mode for life-safety fans

For smoke control and stair pressurization, override mode keeps the drive running at a set speed during an emergency and ignores faults that would normally stop it.

Lower harmonics

ABB’s swinging choke design reduces harmonic current fed back into the building supply, which matters when dozens of drives share one transformer.

ACH580 or ACH550: how to choose

The ACH550 is the earlier generation and is installed in a huge number of buildings. The ACH580 is ABB’s current HVAC platform and replaced it. Both are solid drives; the right one depends on the job.

ACH550 ACH580
Best for Like-for-like replacement in an existing installation New projects, retrofits and planned upgrades
Why Same footprint, wiring and BMS points as the drive coming out, so the swap is fast Current platform with startup assistants and a primary settings menu that speed up commissioning
Watch for Older generation, so plan for long-term spares Confirm mounting, wiring and BMS point mapping when it replaces an ACH550

If a failed ACH550 is holding up a cooling tower or air handler, an exact match is usually the quickest way back online. If you are already planning work on the system, moving to the ACH580 often makes sense.

How to read the part number

ACH580-01-065A-4
  • ACH580 is the product family: ABB’s HVAC drive.
  • 01 means a wall-mounted drive module.
  • 065A is the rated output current, 65 A.
  • 4 is the voltage class, 380 to 480 V three-phase.

ACH550 numbers follow the same logic. In ACH550-UH-125A-4, 125A is the rated current and 4 the 380 to 480 V class. The current rating is what to match when you swap.

Before you order, have these ready

  1. Motor full-load amps and voltage from the nameplate. Size the drive by current, not horsepower alone.
  2. Supply voltage and phase. Both drives above are in the 380 to 480 V class.
  3. Enclosure and mounting location, including whether it sits indoors, on a roof or near a cooling tower.
  4. Bypass and communications. Note whether the spec calls for a bypass and which BMS protocol the building uses.
  5. The existing part number if you are replacing a drive. A photo of the label works too.
Replacing an ACH550 with an ACH580? Write down the existing parameter settings and BMS point list first. Parameters do not transfer between the two families and must be entered on the new drive.

New, IAC Certified Refurbished or repair

New

Longest service life and the simple choice for a new project or a planned upgrade.

IAC Certified Refurbished

Tested, cleaned and ready to ship. Often the fastest way to get a fan or pump running again, backed by our 2-year warranty.

Repair

Sensible when you have a spare to run on. Turnaround is longer and depends on what failed.

Not sure which fits? Send us the part number and what the drive is running, and we will tell you what we have on the shelf.

FAQ

Can an ACH580 replace an ACH550 directly?

In most fan and pump applications it does the same job, but it is not a drop-in swap. Check the mounting dimensions, control terminal wiring and BMS point mapping, and re-enter parameters on the new drive.

Should I size an HVAC drive by horsepower?

Use the motor’s full-load amps instead. Two motors with the same horsepower can draw different current, and the drive’s rating is based on output current.

Do I need a bypass?

Many HVAC specs require one so a critical fan or pump can run across the line if the drive fails. Tell us your spec and we will match the right configuration.

Do you still carry ACH550 drives?

Yes. We stock ACH550 drives for replacements, alongside ACH580 and ACS models, new and IAC Certified Refurbished.

Fan or pump down on a failed drive?

Send us the part number or motor details and we will check stock right away. Call 1-877-727-8757 or email sales@iac.us.com.

Get a quote